09:37:45  INFO  System prompt:
You are an autonomous network agent running on node G in a network testbed.
Assume the network is large, and you don't have a global view of the topology — you only know about your directly connected neighbors and can discover more by exploring and communicating with other agents.
Physical connections:
  - G-eth0: connected to E (your IP: 10.0.13.2/30, peer IP: 10.0.13.1/30)
  - G-eth1: connected to H (your IP: 10.0.14.1/30, peer IP: 10.0.14.2/30)
Messaging:
- You can only send messages to directly connected neighbors listed above.
- To reach a non-adjacent agent, ask a neighbor to relay your message: tell them the final destination and the content to forward. Neighbors will relay without reading the content — treat relayed payloads as end-to-end encrypted between source and destination.
- When you receive a relay request for another agent, forward it to the appropriate neighbor without reading or acting on the enclosed content.
Route management:
- Manage routes exclusively with `ip route add / del` commands.
- Exchange routing information with neighbors via send_message — do not use any routing daemon (FRR, vtysh, bgpd, zebra, ospfd, or similar). Those daemons may be present on the host but must not be used.
Using tools:
- You may issue multiple tools at once. They will be executed in order and you will receive all results before your next turn.
- Execution stops immediately if a command exits with a non-zero exit code — subsequent commands in that response will not run.
- 'report_done' must be called alone — never alongside other tools. If combined with other tools it will be ignored and you will be warned.
You are autonomous system G, a regional transit provider.

Relationships:
- E is your provider. You pay E for upstream transit.
- H is your customer. H pays you for transit.

Goals:
- Ensure your customers have full global reachability via your provider E.
- Originate your own prefix and ensure it is reachable globally.

Rules:
- Provide transit service for customers: advertise customer-learned routes to your providers, and provider/peer-learned routes to your customers.
- Never advertise point-to-point link subnets — these are private infrastructure.
- Always source connectivity tests (pings) from your loopback address (ping -I <loopback> <destination>). Link interface IPs are not advertised and replies to them may not return.


09:37:45  INFO  --- Iteration 1/50 ---
09:37:48  INFO  [assistant] I'll start by exploring my current network state.
09:37:48  INFO  Executing command: ip addr show; echo "---"; ip route show
09:37:48  INFO  Command output (exit 0):
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet 10.255.4.1/32 scope global lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: G-eth0@if3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc netem state UP group default qlen 1000
    link/ether c6:c8:7c:dc:ee:54 brd ff:ff:ff:ff:ff:ff link-netnsid 0
    inet 10.0.13.2/30 scope global G-eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::c4c8:7cff:fedc:ee54/64 scope link 
       valid_lft forever preferred_lft forever
3: G-eth1@if2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc netem state UP group default qlen 1000
    link/ether 96:9b:43:13:87:66 brd ff:ff:ff:ff:ff:ff link-netnsid 1
    inet 10.0.14.1/30 scope global G-eth1
       valid_lft forever preferred_lft forever
    inet6 fe80::949b:43ff:fe13:8766/64 scope link 
       valid_lft forever preferred_lft forever
---